|
|
|
Who's Online
There currently are 5841 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I have this hi-fi system for a long time and I need to repair some things. Founding this manual will be very helpfull :)
 ;
It is pretty good. The schematics were covered all components, the manual also provide the parts list . It's useful for the trouble shooting.
;
Very fast service, best quality of the service manual and the schematics
;
This service manual of the old video cassette recorder VT-LC50EM is very good readable even the tiniest numbers (i.e. IC-pins). The circuits are very clear. Many details of the schematic are very good described but in GERMAN language. Many schematic details - but complete at all. Common background information of several details are enclosed and physical knowledge of the TFT liquid crystal display for example. The manual lacks PCB drawings. If you understand german I would recommend this manual for you.
;
Hi, this is a very clear manual, nice copy, not quite up to the standard of the very best available but better than many others. I think the price was especially fair for a hard to find manual and I would certainly use this manual seller again. Recommended.
The LCD will change as follows. Example: Test disc: TCD-782, DISC type select: CD-d, Judgement value: 7F, Measurement value: 3D BE.
switchover sequence is as stated below. Confirmation mode OFF -> Focus bias (FB) -> Tracking balance (TB) -> Tracking gain (TG) -> Tracking error offset (TEO) -> Focus gain (FG) -> Focus error offset (FEO) -> Confirmation mode OFF Example: Tracking error offset (TEO) Adjustment value: 03
Judgement value Measurement value *All numerical values are displayed in HEX What disc the IC has selected can be understood according to this judgment value. The decision standard of IC is as follow. LCD displays �CD-d� 0 < Judgment value < 10 10 < Judgment value < 32 32 < Judgment value < C8 C8 < Judgment value No disc CD-RW CD-DA and CD-R LCD displays �CD-r� No disc No disc CD-RW CD-DA and CD-R Tracking error offset (TEO) display Adjustment value *Adjustment values are displayed in HEX.
The state of the FE waveform can also be understood from this judgment value. 3. Confirmation of sled movement By pressing the F. SKIP or B. SKIP button continuously when all LCD light up, it is possible to transfer the pick-up to either the outer circumference or the inner circumference (the LCD is to remain all light up). 4. Confirmation of the RF level Test point: RF and VC (Vref) Test disc: TCD-782 Confirm that the RF waveform appears as shown below.
ADJUSTMENT
< TUNER SECTION >
1. DD converter clock adjustment Settings : � Test point : Q204 Collector � Ajustment location: TC208 Method : Set to AM603 kHz and adjust TC208 so that the test point becomes 360kHz. At 0.8Vp-p or greater 2. AM VT Check Settings : � Test point : TP1 (VT) Method : Set to AM 530kHz(AU,ALH), 531kHz(Other) and check that the test point is 1.0V ± 0.5V and set to AM 1710kHz(AU,ALH), 1602kHz(Other) and check the test point is 7.5V ± 1.0V(AU,ALH), 6.5V ± 1.0V (Other). 3. AM Tracking Adjustment Settings : � Test point : HP OUT (VOLUME MAX) � Adjustment location : BAR ANTENA................................600kHz(AU,ALH) BAR ANTENA................................603kHz(Other) TC801..............................................1400kHz(AU,ALH) TC801..............................................1404kHz(Other) * Repeat this adjustment a few times until the wave shape has the maximum amplitude. 4. AM IF Adjustment IFT803.........................................999kHz(Other) IFT803.......................................1404kHz(AU,ALH) 5. FM VT Adjustment(Lower side) Settings : � Test point : TP(VT) � Adjustment location : L801 Method : Set to FM 87.5MHz and adjust L851 so that the test point becomes 1.5 ~ 2.0V. 6. FM Tracking Adjustment Settings : � Test point : HPOUT (VOLUME MAX) � Adjustment location : L802................................................87.5MHz * Repeat this adjustment a few times until the distortion is minimum.
VOLT/DIV: 200mV TIME/DIV: 0.5us 5. Confirmation of tracking balance Test point: TE and VC (Vref) Test disc: TCD-782 Press the DSL button while the test disc is playing and confirm that the traverse waveform is as is shown below.
VC
VOLT/DIV: 200mV TIME/DIV: 2ms 6. Confirmation of each servo It is possible to confirm the adjustment value of each servo by repeatedly pressing the MODE button while the test disc is playing. The
- 24 -
|
|
|
> |
|
