AIWA XPR210
Owner's Manual

M

RADIO RECEPTION

Tuning in to a station � M
1 Press TUNER ON/BAND repeatedly to select AM or FM. 2 Press TUNING + (t) or - (r) to tune in to a station. After listening, press sSTOP/OFF/CHARGE to turn off the radio.

For quick tuning
Keep either TUNING + (t) or - (r) pressed for about 1 second. When a station is tuned in to, the frequency stops automatically. However, it does not stop if the broadcast signal is weak.

1

For better reception � N

FM: The headphone cord functions as the FM antenna. Keep it extended. AM: Turn the unit to find the position which gives the best reception.

To listen to an FM stereo broadcasting

2

When a tuned in station is in stereo, ST changes to . When the FM stereo signal is weak and distorted, press MONO/ST. ST goes out and the sound will be heard in monaural but distortion will be reduced.

Note
� Do not open the disc compartment during radio reception. The buttons will be deactivated. � The power is turned off automatically if no operation is made after 180 minutes from the last operation during radio reception.

N

FM

AM

AM steps � O
Radio broadcasts have different frequency ranges and changes in different steps in different countries. This unit is factory-set to 10 kHz steps on AM. When using the unit where the AM step changes to 9 kHz, set the AM STEP switch on the inner side of the disc compartment to 9 kHz. � When the AM step is changed, stations that you preset are erased.

Presetting stations � P

O
AM STEP 9kHz 10kHz

You can preset up to total of 30 stations on AM and FM. 1 Press TUNER ON/BAND repeatedly to select AM or FM. 2 Press TUNING + (t) or - (r) to tune in to a station. 3 Press ENTER/DISP to preset the station. a Preset number To preset more stations, repeat steps 2 and 3.

Listening to preset stations � Q
1 Press TUNER ON/BAND repeatedly to select AM or FM. 2 Press PRESET CALL i/k repeatedly to select the preset number. After listening, press sSTOP/OFF/CHARGE to turn off the radio.

P

1 Press PRESET CALL i/k repeatedly to select the preset number you

Changing the presetting

wish to change. 2 Keep ENTER/DISP pressed for 1 or more seconds until the preset number and the frequency flash. 3 While the preset number is flashing, press TUNING + (t) or - (r) to tune in to a station. 4 Press ENTER/DISP to preset the station on the selected preset number. If the flashing stops, repeat the procedure from step 2.

Erasing the presettings one by one

1 2 3
ENTER/DISP

Press sSTOP/OFF/CHARGE after step 2 in �Changing the presetting� above. Each preset station is erased. All the settings move up by one and the preset numbers are refreshed.

Erasing all of the presetting
Keep ENTER/DISP pressed, then press TUNER ON/BAND when the frequency and preset number starts flashing.

CONNECTING TO AN EXTERNAL UNIT � R
Use a commercially available connection cord which has a 3.5 ø stereo miniplug at one end and two phono plugs at the other end. Connect the stereo mini-plug to the PHONES/LINE OUT jack of the unit and connect the phono plugs to the analog input terminals of the external unit.

Note
� Turn off the power of both units before connection. � DO NOT connect to the PHONO inputs of an amplifier (with a built-in phonoequalizer-amplifier). � Adjust the volume and DSL on this unit.

Q

MAINTENANCE
To clean the lens � S
If the lens becomes dirty, the player will skip or not play. If this occurs, clean the lens in the following manner. To remove dust or dry particles, first use a camera lens blower/brush a to blow a few times to loosen particles, then gently brush the lens b clean. Finish by blowing the lens again.