|
Who's Online
There currently are 5856 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Even if the PDF is a scan, I can read the information I need.
The price is affordable and the service (mail sending) is very fast.
Thanks ! Regards. William (Fan of Kenwood)
;
Very good quality original datasheet!I like this amazing website!!!!!!
;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
ADJUSTMENT
<TAPE PLAYER SECTION>
A MAIN C.B
6
8
8
6. Tape Speed Adjustment Settings : � Test tape :
TTA�100
SFR 1
D C B A
(TAPE CENTRE) � Test point : Phones Jack (J1) � Adjustment location : SFR1 � Tape/radio : TAPE � S-BASS : OFF � Volume : NON-CLIP Method :
VR1
* *
(MAX -10dB ) Play back the test tape and adjust SFR1 for 3000Hz ± 10Hz. Then confirm WOW is less than 0.50%.
42
VOLUME
L102
5 3
VC101
TP1(VT) * * L103
7. Azimuth Adjustment Settings : � Test tape : � Test point : � S-BASS : � Tape/radio : � Volume : � Adjustment location : Method :
PHONES
TTA�330/TTA�420 Phones Jack (J1) OFF TAPE MAX Head azimuth adjustment screw Play back the 8KHz signal of the test tape and adjust the screw so that the output becomes maximum.
L105
J1
4 3
L101 (BAR-ANT) P HEAD
1
6
7 FWD
NOTE : * : On the other componets side.
8. Maximum Output Power Adjustment Settings : � Test tape : TTA�210 � Volume : MAX � S-BASS : ON Method : For <YU, YL> : � Short the shorting point B and C only. For <YZ> : � Short the shorting point B and C . � If output is less than 1.2mW(0.14V), short the shorting point A and D . � If output is more than 3.9mW(0.25V), open the shorting point B and C and short the shorting point A and D .
<RADIO SECTION>
1. AM IF Adjustment L105 ....................................................................... 450kHz 2. AM VT Check Settings : � Test point : TP1 (VT) Method : Set to AM 530kHz and check that the test point is more than 0.8V. Then set to AM 1710kHz and check that the test point is less than 8.7V. 3. AM Tracking Adjustment L101 ....................................................................... 630kHz VC101 .................................................................. 1440kHz 4. FM VT Adjustment Settings : � Test point : TP1 (VT) � Adjustment location : L103 Method : Set to FM 76MHz and adjust L103 so that the test point becomes 1.0V ± 0.1V. Then set to FM 108.1MHz and check that the test point is less than 8.5V. 5. FM Tracking Adjustment L102 ..................................................................... 76.0MHz
31
IC101
32
|
|
|
> |
|