|
Who's Online
There currently are 5861 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
;
I'm very satisfied with my purchase. It resolved my problem. Owner-manuals.com is a very very good place.
Thank you!
ADJUSTMENT
A MAIN C.B
1
2
2
VOLUME VR101
SFR 301
1
2
3
IC301
TP2 (L-CH)
TP1 (R-CH)
2
4
2
GND
IC701
PHONES J101
1
<TAPE PLAYER SECTION>
1. Tape Speed Adjustment Settings : � Test tape : TTA � 100 (Tape center) � Test point : Phones Jack (J101) � Adjustment location : SFR301 � Dolby : OFF � MSP : CLASSIC � DSL : OFF � Tape selector : NORMAL(AUTO) � Volume : MAX Method : Play back (FWD) the test tape and adjust SFR301 so that the frequency becomes 3015Hz ± 10Hz. Then confirm WOW is less than 0.50%.
PRACTICAL SERVICE FIGURE
<TAPE SECTION>
Tape speed : Wow : Take-up torque : F.F torque : REW torque : Back tension : S/N ratio : Distortion : Noise level : 3015Hz ± 50Hz Less than 0.55% (RMS) 20 ~ 30g-cm (FWD) 70 ~ 150g-cm 70 ~ 150g-cm 1.0 ~ 3.0g-cm (FWD) More than 42dB (PB, DC) Less than 3.0% (PB, DC) Less than 3.0mV (Vol MAX, PB, DC) Less than 0.4mV (Vol MIN, PB, DC) 63Hz + 3 / � 5dB ~ 8kHz + 4 / � 4dB (NORMAL) 63Hz + 3 / � 5dB ~10kHz + 4 / � 4dB (CrO2) TTA � 100 TTA � 200 TTA � 320(NORMAL) TTA � 310(CrO2)
2. Dolby Level Adjustment Frequency response : Setting : � Test tape : TTA � 200 � Test point : TP1(RCH),TP2(LCH) � DSL : OFF � Tape selector : NORMAL Test tape : � Dolby SW : OFF � Volume : MIN � Adjustment points : Soldered patterns 1 � 4 Procedure : Short the patterns via solder as showen in the table so the Dolby NR level is 24.5mV ± 1.0dB. Adjust so the specifications are satisfied in both the forward and reverse directions. Connect 10mF /16V coupling capacitors between test points and test equipment (connect the positive terminals to the test points). SOLDER PATTERN 1 � 4 STANDARD : 24.5 ± 1.0dB SOLDER POINT INCRESE LEVEL 1 only +1dB Lch
2 1 3
only and 2
+1.5dB +2.5dB +1dB +1.5dB +2.5dB
Rch
only 4 only 3 and 4
1 1
|
|
|
> |
|