|
|
|
Who's Online
There currently are 6041 guests and
2 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
IC DESCRIPTION
IC, ML63512A-A07 Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ~ 26 27 28 29 30 ~ 31 32 33 34 35 36 37 38 39 40 41 42 43
Pin Name
DSL CTRL SLAVE S-CLK DSL EFFECT SLAVE S-DATA AU F/R CTRL MUTE MOTOR HI-SP MOTOR HI-SP MOTOR DRCT MOTOR CTRL MOTOR BRAKE DIS-CHARGE VOLTAGE DET 1 VOLTAGE DET 2 K-MAIN K-REMOTE NC P-CTRL LED CTRL MOTOR CTRL VDD I VSS VDD VDDH CB1 ~ 2 VDDL XT0 XT1 TST1B ~ 2B VSS OSC 0 OSC 1 RESET BEEP CASS SW P-DET MS DET TIMING SW REMOTE SEL NC DOLBY CTRL
I/O
O I O O O O O O O O O O I I I I � O O O � � � � � � I O I � � � I O I I I I I � O
Description
DSL switch control output terminal. (Not used) Serial clock input terminal for remote controller. (Connected to GND) DSL switch control output terminal. (Not used) Serial data output terminal for remote controller. (Not used) Playback signal FWD/REV switching output terminal. Mute signal output terminal. Motor HI-SP turn over output terminal. Mecha deck motor high speed control output terminal. Mecha deck rotating direction control output terminal. Mecha deck motor control output terminal. Mecha deck brake control output terminal. Dummy load control output terminal when checking battery level. Voltage detection input terminal 1. Voltage detection input terminal 2. Main unit key input terminal. (Using level detector) Remote controller key input terminal. (Using level detector) Not connected. Auto stop LED control output. Battery level indication LED control output. Motor control turn over output terminal. External equipment interface power supply terminal. Negative ( � ) side power supply terminal. Positive ( + ) side power supply terminal. Boost power supply terminal for back up. Capacitor connection terminal for boost power supply. Positive ( + ) side power supply terminal for internal logic. Connect 32.768 kHz crystal oscillator. Test terminal. (Connected to VDD) Negative ( � ) side power supply terminal. Clock oscillator terminal for high frequency side. (Not used) RESET input terminal. Beep sound output terminal. Cassette tape existance detect switch input terminal. Auto stop signal detection input terminal. Music sensor detection input terminal. Mecha deck timing switch detection input terminal. Remote controller specification switching input terminal. (Not used) Not connected. Dolby control output terminal. (Not used)
�7�
|
|
|
> |
|
