|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
CD TEST MODE
1-1 How to Activate CD Test Mode 1) Connect 62 pin (test) of IC701 (LC72358N-9910) on MAIN C.B to the 31 pin (VDD) by cable. Caution when servicing (1) How to use extension jig. Correct between MAIN C.B. and CD mechanisms by extension jigs when checking CD mechanism (TN-CCD1001-113J) operation. (Refer to the following figure.)
2) Connect wire of ACC (red) and BACKUP (yellow) of power supply/speaker connector to DC+12V, then connect Ground (black) to -. When CD test mode is started, all displays will be lighted as shown in the following figure.
1-2 How to cancel CD Test Mode 1) Disconnect the cable of 62 pin (test) and 31 pin (VDD) of the MAIN C.B IC701 (LC72358N-9910) and switch on the power. 1-3 CD Test Mode Functions MODE Keys to operate Start Mode Search Mode RANDOM Display All lightented TOC READING Operations � Continual Focus Search (The pickup lens respeats the full-swing up-down motion) * NOTE 1 � Normal Play Back � Focus search is contiuned if TOC cannot be read � Pause Status � Pick up Move to outer most track � Pick up Move to inner most track � Step 1 : For CD/CD-R � Step 2 : For CD-R RF Gain is up against Step 1 � Step 3 : For CD-R Laser Power Up against Step 2 Contents � Start TEST MODE � Confirm APC circuit � Laser current measurement � Confirm focus error waveform � Focus servo � Traking servo � CLV servo � Sled servo � Traking servo OFF � Thread servo � Confirm mechanism operation � Step 1 to 3 are cyclic � �Error 03� is indicated if the Disc does not Step 1 match. Parts Description AKC-JIG Parts Number SV-J00-075-010
Play Mode
REP 1
Traverse INT Mode Thread Mode Gain Switch 1 (Preset Button)
TRACK No. Playing Time Indication Revel/Ing Indication Track no. & Playing Time Indication All lightened All lightened
� Do not insert a Disc when confirming Search Mode � Press PWR button when cancelling Search Mode. Test Mode will be restored when PWR button is pressed once again. � Insert the �Test Disc� when operating all modes except search mode. * NOTE 1 : There are CD operations are disable owing to the protection circuit being operated when heat builds up in the driver IC if the focus search is operated continually for more than 10 minutes. In cases, the power supply should be switched off for 10 minutes until heat has been reduced and then re-started.
-27-
$4.99 CDCX407 AIWA Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|