|
Who's Online
There currently are 5937 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
thank u so much for this manual that was so cheap that i thought it was a scam but i gambled anyway because it was too good of a deal to pass up and behold,the manual has everything and details of everything even the screws and im still amazed and very happy with my manual .so take my word and jump on it before they realize how cheap they selling thier manuals..thank you so much for taking time to read my thoughts
;
I do not have very much to say.
The price is quite covenient, delivery was better as promised (about 12 ours, against the specified 24 hours if I remember well), and the quality of the PDF is more than acceptable.
The Service Manual of Sansui R30 itself is also satisfactory: good graphic for schematics and layouts, simple and well structured.
Giovanni Bianchi
;
Happy to find finally a schematic for this amplifier. The schematic is of good quality, the pcb layout is useless: all is black. Never the less, it is very easy to find the components on the board using the schematics.
;
Hard to find manual was ready the next day. Scans were very legible (including schematics). All the essential parts of the service manual were present (adjustment procedure, schematics, and parts list). It would have been nice if the rest of the manual was included (disassembly procedure, theory of operation, etc.).
;
The Service Manual for the Kenwood KR-V55R provided by owner-manuals.com was as described/advertised. The contents provided the necessary information to effect a diagnosis of the unit. The schematics above all else was instrumental in tracing the the signal flow from component to component.
CD TEST MODE
1. How to activate CD test mode 1) Remove the resistor R907 (100k�) from the MAIN C.B, and add R999C 22k� or chip resistor to the MAIN C.B. (Fig. 1) 2) Connect +12V to ACC/BACK UP and � (minus) to the ground of the CONNECTOR ASSY. 3) Turn on the power. 4) Test mode will be activated and all LCD display will light up. (Fig. 2) 3. CD test mode functions Mode Start Mode Operation Key LCD Display All LCD light up DISC LOADING Operation Contents Activate test mode � Loading � All servo off � Laser on � VCC on � Continual focus search � Check APC circuit Search Mode RANDOM (The pickup lens repeat the � Laser current measurement full-swing) � Check focus error waveform * NOTE 1 � TOC reading � Normal playback Play Mode Fig. 1 REPEAT 1 � Display Track No. and Play time � Display Level/Ing. � Same operation as search mode if TOC cannot be read � SLED servo Traverse Mode Stop Mode INT REPEAT � Display Track No. and Play time All LCD light up Playback pause status Wait status Tracking servo off � All servo off � Laser on/off � Pickup moves to outer track Sled Mode All LCD light up � Pickup moves to inner track � Check mechanism operation � Sled servo � Tracking servo � CLV servo � Focus servo
�
UNLOADING DISC CHUCKING
�
� Do not insert the CD disc when checking the search mode. � Press the REPEAT key to release each mode. Fig. 2 2. How to cancel CD test mode 1) Turn off +12V to ACC/BACK UP 2) Solder back the resistor R907 (100k�) and remove the R999 (22k�) from the MAIN C.B 3) Disconnect +12V from ACC/BACK UP and � (minus) from the ground of the CONNECTOR ASSY. * NOTE 1 : There is a case that the CD cannot be operated owing to the protection circuit being operated when heat builds up in the driver IC if the focus search is opereated continually for more than 10 minutes. In this case, the power supply should be switched off for 10 minutes until the heat has been reduced and then re-start.
� 28 �
|
|
|
> |
|