|
Who's Online
There currently are 5716 guests and 2 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This document is just what I was looking for, it´s very useful, it contains adjustment procedures for the final stage of the power amp and also
has a complete wiring diagram and description of the main semiconductors used in the design.
;
Dear Sirs,
Thank you for the fast support, the manual does provide all necessary information to repair the radio. All schematics are in a good quality for reading.
The manual fits 100% to my requirements as a technican.
Kind regards Thomas
;
the big video recorder format s-vhs many features delicate in loading system of the cassette. Such machines are no longer manufactured, it would be too expensive.
;
THIS MANUAL IS VERY GOOD AND VERY CLEAR
PLEASE NOTE IT DOES NOT CONTAIN THE SETUP INFORMATION TO ALIGHN THE GEARS IN THE CD MECH IT DOES SHOW ALL THE PARTS AND THEIR LOCATIONS .
;
Complete service and operation manual. All schematics are there, all circuit boards AND add-on boards. Including exploded views ,component names and specifications. Also electrical and mechanical adjustment procedures are in this manual. This manual also covers the more advanced BR-S811E unit. Scan quality is fair and usable.
(5)
Wiring to P.W.B. (Refer to Fig-5/6). � Be sure to connect the wires coming from the P.W.B. JIG to the same connecting points on the P.W.B. MAIN as follows; 1) Connect the motor wires and sensor (PS201) wires that are removed in step (2) to the P.W.B. JIG. 2) Connect all wires coming from the P.W.B. JIG to the respective lands of the P.W.B. MAIN by soldering. � Connect the motor wires (BLU/WHT) of the P.W.B. JIG to the motor wire connecting lands on the P.W.B. MAIN by soldering. � Connect the LED (LED201) wires (RED/GLY) of the P.W.B. JIG to the LED wire connecting lands on the P.W.B. MAIN by soldering. � Connect the sensor wires (BRN/BLK) of the P.W.B. JIG to the sensor wire connecting lands on the P.W.B. MAIN by soldering. � Connect the sensor (PS201) wires (YEL/ORG/ RED/BRN) of the P.W.B. JIG to the sensor wire connecting lands on the P.W.B. MAIN by soldering. � Connect the SW202 wire (WHT) of the P.W.B. JIG to the SW202 wire connecting lands on the P.W.B. MAIN by soldering. � Connect the SW203 wire (BLK) of the P.W.B. JIG to the SW203 wire connecting lands on the P.W.B. MAIN by soldering. � Connect the SW402 wires (BLU/WHT) of the P.W.B. JIG to the leads of SW402 on the P.W.B. MAIN by soldering. (Refer to Fig-6)
Fig-5
(6)
How to use the repair jig When the Control Unit (CDC/CT) is used 1) After all wires and connections are complete, connect the cable to Control Unit (CDC/CT) and DIN jack of P.W.B. FLEX. 2) Connect external power +12 V to ACC/BACKUP wire and ground (-) to the GROUND wire. 3) Check the operation. When the Control Unit (CDC/CT) is not used 1) Connect the supplied P.W.B Key to the P.W.B. MAIN by performing all connections between them (Refer to Fig-7/8). (Wires to be used for connecting the P.W.B Key are not supplied.) P.W.B Key HOT GND P.W.B MAIN TO GND
Fig-6
-3-
|
|
|
> |
|